Izdelki za sikantal epoksi (21)

Eine industrielle Bodenbeschichtung, die dank ihrer Epoxidharz-Basis enorm chemikalienbeständig ist. In vielen Farben und den Versionen Säureresistent, Anti-Rutsch, Kalttrocknend, Rapid verfügbar.

EG 91 Epoxy-polyurethane two-component elastoplastic and thixotropic sealant, for joints subject to traffic, where Shore A Hardness Scale = 65. The elongation-at-break is 70%. To be applied with a trowel or extruded into the suitably-taped sections of the joint (to protect adjacent surfaces). Resistant to contact with hydrocarbons (gasoline and diesel fuel). Horizontal sealing of joints in industrial flooring, even in the presence of chemical attacks and stresses from average-heavy traffic. Vertical sealing of joints in concrete works and products. The application and containment surfaces (joint walls) should be clean, dry, conveniently prepared and adequately resistant: free from dust, grease, soiling, crumbling and/or non-adhering parts and dry. The application surfaces must also be preliminarily treated with Protech Flex Primer. Add component B to component A taking care to pick up all the material contained in the packs, mix thoroughly with a mixer at a low number of revolutions, until a perfectly homogeneous mix is obtained; add the required load amount (component C) continue to mix until a perfectly homogeneous mixture is obtained, indicated by the uniform colour of the mixture. Apply the product mixed by trowelling or with extrusion guns. Do not apply with temperatures below + 5°C or higher than + 35°C and in the presence of surface stagnant water. Approximately 1.25 kg of EG 91 per cubic decimetre of joint volume to be sealed (1250 kg per cubic metre). Packaging: Kit of 5+2.5 kg UM: €/kg

Das Epoxidharz-System E30RB ist eine 2K Epoxi-Rollbeschichtung mit mittlerer Verarbeitungszeit für hochwertige Boden- und Wandbeschichtungen ähnlich RAL7032 kieselgrau.

2component epoxy paint for the protection of concrete floors, metal structures, etc. Does not contain solvents (100% solids). Features Excellent adhesion. Great penetration power. Good adhesion in wet substrate with high percentage of humidity. Good capacity for reaction at low temperatures and high percentage of humidity. Indoor and outdoor use.

Nummer Eins chemicals 2008 Yılından beri Kimya sektöründe edinmiş olduğu tecrübeler ışığında müşterilerine en iyi ürünü ve hizmeti sunma felsefesi ile yola çıkarak İSTANBUL tuzla’da A.O.S.B de Epoksi ve Poliüretan Yapı Sistemleri, Antikorrozif epoksi ve poliüretan çelik konstrüksiyon ürünleri, Ahşap ve Metal tekneler için epoksi ve poliüretan ürünler, Su bazlı polimer esaslı su yalıtım sistemleri İç ve Dış mekanlarda kullanılan kaplama sistemlerine yönelik ürünlerin üretimine devam etmektedir. Firmamız kaliteli üretim kaliteli ürün anlayışı ile Avrupa normlarına uygun laboratuar cihazları ve analiz ekipmanlarına sahip ARGE ve Kalite Kontrol Laboratuvarında konusunda uzman mühendis ve kimyager kadrosu ile günümüz dünyasındaki teknolojik gelişimleri yakından takip ederek ürünlerini sürekli geliştirmekte ve yenilikçi bir anlayış ile çalışmalarını sürdürmektedir.

Universeller, kraftvoller Kontaktkleber geeignet für Holz, Kunststoff, Furnier- und Kunststoffkanten, Metall, Gummi, Leder, Filz, Weichschaumstoffe, Papier, Pappe u.v.a. Kontaktkleber mit starker Soforthaftung. Flüssig, leicht verstreichbar und schnellanziehend, ideal für glatte Oberflächen. Elastische Klebeverbindung, hohe Endfestigkeit, wasserbeständig. Universell einsetzbarer Kontaktkleber, der leicht verstreichbar ist und schnellanziehende Kontaktklebungen ermöglicht. Permanent elastisch, gleicht Materialspannungen aus, daher ideal für flexible Materialien. Nicht geeignet für Styropor®, Weich-PVC, PE, PP. Temperaturbeständig +80°C Alterungs- und ozonbeständig UV- und IR-stabil Widerstandsfähig gegen eine Vielzah von chemischen Medien Elastisch und wasserfest Verarbeitung/Gebrauchsanleitung Oberflächen müssen sauber, öl und fettfrei sein. Zweiseiten-/ Kontaktklebung: Klebeflächen gleichmäßig dünn einstreichen, saugfähige Materialien evtl. mehrmals. Ablüften lassen. Wenn...

DÉFINITION TECHNIQUE Enduit décoratif à projeter en pâte prête à l’emploi pour un usage en murs et plafonds intérieurs. Permet de rattraper dans une certaine mesure les défauts du support tels que bullages et balèvres. Peut être appliqué en tant qu’enduit de lissage ou en relief structuré type « gouttelette ». Différentes teintes et qualité lavable sur demande. DOCUMENTS À CONSULTER DTU 59.1. PV CSTB N°R.A.97.179 : classement au feu MO. COMPOSITION ET ASPECT Résine acrylique en émulsion, charge minérale, dérivés cellulosique, agent de conservation et divers adjuvants. La pâte est de couleur blanche et de consistance adaptée à la projection mécanique. CARACTÉRISTIQUES TECHNIQUES • Extrait sac : 72% • Densité : 1,6 SUPPORTS ADMIS Béton plus ou moins bullé, béton brut de décoffrage, béton cellulaire, carreaux de terre cuite, première couche lissée de SOLIDECOR, agglos, enduits plâtre, anciennes peintures, enduit ciment, carreaux de plâtre, plaques de...

Silicone Sealant S-200 Hoogwaardige, zuurvrije, sanitaire siliconenkit. Toepassingsgebied Voor het afdichten van naden, voegen en kieren in o.a. badkamer, toilet en keuken. Hecht o.a. op acryl, PVC, tegels, emaille, metaal, RVS en glas. Poly MaxFix & Seal Express Oplosmiddelvrije montagelijm en afdichtingskit met zeer hoge elasticiteit en zeer snelle sterkteopbouw op basis van SMP-Polymer. Ideaal voor monteren in combinatie met afdichten. Toepassingsgebied Voor het lijmen en monteren van vele bouwmaterialen op vrijwel alle ondergronden, zoals hout, (natuur)steen, (gas)beton, metaal, hardschuim en diverse kunststoffen. Geschikt voor binnen- en buitentoepassingen, zoals regelwerk, plinten, schroten, vensterbanken, plaat- en isolatiematerialen. Tevens geschikt het afdichten van voegen, naden en kieren bij (kunststof) kozijnen, boeiboorden, daken, dakgoten, muren, lichtkoepels en schoorstenen. Voor alle professionele toepassingen, zoals gevel- en interieurbouw, woning-, utiliteit-

ADLER PUR-based coatings are modern solvent-based systems that meet the most demanding standards in furniture and interior decoration. The best resistance, both for chemical and mechanical stresses and strains, as well as ease of application and use are the special features of this type of coating system. ADLER offers the best choice of PUR-based coatings for the most diverse types of wood as well as the most varied design concepts. Premium quality and efficient use are always ensured in the process. In this manner, you can meet almost any need or requirement for the surface as desired by your customers.

Himfloor ML4000 est un revêtements à base de résine époxy et sables extrasilicieux colorés - version monochrome – avec un rendu plus ou moins texturé, selon le coefficient de glissance souhaité. C’est un revêtement de sol adapté à un trafic piétonnier et industriel intense. Il convient aux lieux où l’on désire un sol avec un aspect décoratif et une bonne résistance à l’usure dans le domaine piéton (se référer à leur Avis Technique pour les locaux concernés), mais ils conviennent aussi au domaine industriel. Cantines, cafétérias, toilettes, vestiaires, surfaces commerciales, halls d’exposition laboratoires, industries variées telles que celles du pharmaceutique, de l’agro-alimentaire, de la mécanique de l’électrique… Caractéristiques : Hygiène: système dense, imperméable, facile à entretenir ; Aspect décoratif: variété de teintes ; Différentes textures/rugosités de surface : Durabilité: bonne résistance aux trafics piéton et industriel ; Résistance à de nombreux produits chimiques.

Pardoseala epoxidica cu granule colorate Emex Quartz - See more at: http://www.e - Pardoseala Epoxidica Decorativa EMEX QUARTZ este un produs profesional, pe baza de rasini epoxidice fara solvent, disponibil intr-o gama infinita de modele obtinute prin inglobarea de granule de cuart sau marmura divers colorate in masa pardoselii. Acest tip de pardoseala se mai numeste si covor epoxidic. Produsul poate inlocui cu succes mozaicul sau gresia, avand in primul rand avantajul aspectului superior, dar fiind si o alternativa mult mai rezistenta atat la utilizare dar si in timp a acestora. Caracteristici principale: - Produs agrementat sanitar; - Aderenta excelenta la suport; - Etalare de exceptie; - Duritate excelenta; - Durabilitate mare; - Rezistenta mare la abraziune; - Rezistenta excelenta la uzura; - Rezistenta mare la agenti corozivi; - Rezistenta mare la hidrocarburi, medii acide sau alcaline.

SOLVENT PAINT of COSMOCHROME is a high quality undercoat for concrete surfaces (concrete columns, concrete floors, walls, ceramic tile roofs etc). It is highly durable against extreme weather conditions and atmosphere pollution. It has strong adhesion, great covering power and extreme hardness PACKAGE:0,75 LT, 10 LT, 2,5 LT COLOR:Black, Cypress Green

Poliuretano (5,0 kg) + endurecedor (0,7 kg) es decir, un kit de 5,7 kg Aplicaciones: Para todos los revestimientos de suelos interiores o exteriores de caucho, en losetas o en rollo, las moquetas y los céspedes sintéticos. Ventajas: Apto para el encolado de numerosos revestimientos y sobre soportes tales como hormigón y aglomerados. Recomendado para los usos intensivos. Gracias a su flexibilidad, puede ser sometido a importantes variaciones de temperatura

SOMAFIX Multi Purpose Hibrid Adhesive is a one-part, a strong adhesive based on a hybrid polymer. It is solventfree, fast curing, paintable, odorless and has a good elasticity characteristics after curing.

EXCOR UNICO è un espanso morbido a celle aperte, imbevuto di VCI e di 5 mm di spessore. Grazie alla sua struttura a spugna, dispone di un’enorme superficie di erogazione e fornisce così all’imballaggio velocemente la giusta quantità di VCI. Negli imballaggi con pellicole di grande volume, l’espanso UNICO si impiega come rinforzo. L’espanso UNICO è disponibile in rotoli o fogli, non rilascia odori, è asciutto e resistente all’invecchiamento. Per fissare il prodotto sulle pareti o sui soffitti, su richiesta del cliente, EXCOR può dotare il prodotto di autoadesivo.

Syntech Poliurea Primer – Epoxy Metal Syntech Poliurea Primer – Epoxy Metal is a two-component primer based on epoxy resins free from solvents, used to promote adhesion, as a surface sealant for concrete, applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. Adhesion promoter, surface sealant for concrete, to be applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. The application must take place on a dry and degreased surface; the substrate must not have crumbly or detached parts and with a degree of humidity that must not exceed 5%. Preparation of the substrate may require some types of mechanical action: Smoothing, bush-hammering, shot peening, hydro-washing. Other mechanical actions that can make the support suitable. The individual components must be mixed carefully until a homogeneous mass is obtained. The material can be applied by roller, brush or spray by means of special airless machines, even in two coats. The temperature of the support must always be at least 3°C higher than the dew point temperature. Minimum application temperature +5°C, maximum temperature +35°C. Approximately 0,20 kg of Syntech Poliurea Primer – Epoxy Metal for every square metre of surface to be treated. Can 10 kg [A] - Can 5 kg [B] - Kit: 1 Can 10 kg [A] + 1 Can 5 kg [B]

Syntech Poliurea Top Coating A protective, pigmented, two-component formulation based on aliphatic polyurethane resins, ideal as a protective and aesthetic coating on waterproofing with SYNTECH POLIUREA SPRAY. Characterised by high levels of elasticity and elevated protection, even in aggressive atmospheres. Available on request in shades from the RAL colour range. Surface coating pigmented for colouring polyurethane claddings, and their protection from UV rays (which in the absence of the top coating would alter the colour over time). After suitable priming with SYNTECH POLYUREA PRIMER, it can also be applied as a simple coloured aliphatic protective coating. Polyurea support Vacuum and blow the surfaces to eliminate any dust that may have accumulated in the 24-48 hours following the installation of SYNTECH POLIUREA SPRAY Support in concrete, mortar, brick, tiles The support on which the polyurea system must be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 3%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. In case of presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to apply in advance the epoxy resin for "wet substrates" Syntech Pavidamp. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. It is recommended to use Primer from the SYNTECH POLIUREA PRIMER range. On particularly absorbent substrates, to avoid the formation of craters / blowholes on the surface of the freshly sprayed product, it is recommended to use primers from the SYNTECH POLIUREA PRIMER range, always contacting the Azichem technical staff for clarification on the most suitable type to use. Apply several layers of primer until the porosity is saturated and providing a light dusting with clean and dry quartz sand (0.4-0.7 mm). Never dust off the primer. Provide suitable elastic sealing systems to cover joints, fittings, cracks or fissures subject to significant movements. Pour component B with component A into a single container, taking care to remove all the material from the packaging. Mix thoroughly with a mixer at low revs, until a lump-free mixture is obtained. Apply with a roller or brush on the surfaces of SYNTECH POLYUREA SPRAY, within 24-48 hours of spreading the latter. A thorough sanding of the supports is recommended for any repairs and/or finishes. From 0.15 to 0.25 kg of SYNTYECH POLIUREA TOP COATING for each square metre of surface to be covered. Can 6.7 kg [A] - Can 3.3 kg [B] - Kit: 1 Can 6.7 kg [A] + 1 Can 3.3 kg [B]

Vopseaua Clorcauciuc pentru Pardoseli EMEX este un produs monocomponent, profesional, pe baza de emulsii de cauciuc clorurat, pigmenti, aditivi, plastifianti si solventi specifici, cu adaos de alfa corindon sau faina de cuartz pentru duritate. Produsul, foarte rezistent atat la apa cat si la frecare sau abraziune, are ca destinatie principala vopsirea pardoselilor din beton, fie pentru protejare, fie doar pentru marcare (eventual cu adaos de micro-perle din sticla). Vopseaua Clorcauciuc poate fi colorata in orice nuanta a cartelei RAL. Caracteristici principale: - Produs agrementat sanitar; - Aderenta ridicata la suport; - Aplicare si intretinere usoara; - Duritate excelenta; - Putere mare de acoperire; - Rezistenta mare la abraziune; - Rezistenta excelenta la uzura; - Rezistenta mare la agenti corozivi; - Rezistenta mare la intemperii, factori chimici, frecare.

Acrylic solvent base paint with good adherence, high mechanical resistance and anti slip properties. Paint for horizontal marking of floors of concrete, cement, asphalt, etc. for parking lots and areas, sidewalks, crosswalk, etc. Colours: White, Yellow (Ral 1003), Red (Ral 2002), Blue (Ral 5015).

Syntech HAG Acryl Syntech HAG Acryl is a four-component resin that reacts to form an elastic and durable gel. The properties of Syntech HAG Acryl are: • Good general chemical resistance. • Does not contain acrylamide, methacrylamide, formaldehyde or solvents. • Not inflammable. • Excellent adhesion on mineral building materials such as concrete, cement and bricks. • The reaction speed can be adjusted from a few seconds to several minutes. • When the injected cracks dry out due to temperature or groundwater level fluctuations the gel does not crack easily. • The hardened gel has excellent durability in wet-dry cycles. Syntech HAG Acryl components are supplied ready to use. Create 2 mixes in separate plastic buckets. Prepare only the quantity to be used each time. Solution 1: Syntech HAG Acryl component A (25 kg resin) mixed with Syntech HAG Acryl component B (2.5 kg catalyst). Solution 2: Syntech HAG Acryl component C (2 packs of 0.625 kg) mixed with clean tap water. Attention: The amount of water must be equal in volume to solution 1. When mixing resin, always use a wooden or stainless steel spatula. The reaction time depends on the temperature of the material, the structure of the building and the possible amount of water present. Higher temperature will speed up the reaction time and lower temperature will slow it down. It is advisable to carry out an on-site test, before injection, to observe and define the reaction time. To change the reaction time, only adjust the amount of Syntech HAG Acryl component C. The amount of the other components remains the same. Use a two-component stainless steel pump (manual, electric or pneumatic). Check that the pump and equipment are clean and that there is no residue from previous injection work. The two mixtures are fed into the pump separately, but are mixed homogeneously at a volumetric ratio of 1:1 in the pump's mixing head, before being injected through the pump nozzle. Check the quality of the concrete, as injection involves pressure. Sealing and waterproofing of cracks and cavities in walls, floors, concrete constructions, underground structures, etc. It can be used in constructions that are not permanently in contact with water (fluctuating groundwater level). Injection of very fine cracks. Determine the type and size of packers based on your pump and injection type. If reinforcing steel is present, try to locate it and plan the drilling pattern so that the reinforcement is not drilled. Drill holes at an angle of approximately 45° or less and in the direction of the crack. Make sure the hole goes through the crack. The distance of the drilled holes depends on the width of the crack. Place the packer in the hole. Prepare the pump to start the injection. The injection pressure varies depending on the structure and size of the crack. Start the injection at the lowest point of the crack. Continue injecting until resin flows out of adjacent packer(s). This is necessary to achieve uniform distribution of the material. Stop pumping, unplug and move on to the next packer. Continue the procedure until the crack is completely filled. After the material has cured, the packers can be removed. Holes drilled can be covered with Repar Tix Speedy HP quick-setting mortar. Clean and rinse the pump equipment with water whenever there is a stoppage longer than 15 minutes and, after completing the injection, rinse with a sufficient amount of water. Make sure the pump is clean and stop only when clean water comes out of the pump. The consumption of the product depends on the size of the empty volume to be filled. Can 25 kg [A] - Plastic can 2.5 kg [B] - Canister 0.625 kg [C] - Canister 0.625 kg [D] - Kit: 1 Can 25 kg [A] + 1 Plastic can 2.5 kg [B] + 1 Canister 0.625 kg [C] + 1 Canister 0.625 kg [D]

COMPOSITION ET ASPECT Blanc &amp; incolore. CARACTÉRISTIQUES TECHNIQUES • Temps de formation de peau : environ 10 minutes (23°C, 50 % HR) • Temps hors poussière : environ 20 minutes (23°C, 50 % HR) • Allongement à la rupture: 150 % • ÉPAISSEUR polymérisé : en 24 h (23°C, 50 % HR) 3 mm • Température d’application : + 5°C à + 40°C CONDITIONNEMENTS Cartouche de 310 ML. STOCKAGE 18 mois à l’abri du froid et des fortes chaleurs en emballage d’origine non entamé. PRÉCAUTION D'EMPLOI Éviter le contact avec la peau. En cas de contact avec les yeux, laver immédiatement avec de l’eau et consulter un spécialiste. Conserver hors de portée des enfants. PRÉPARATION DES SUPPORTS Les supports doivent être propres, secs, sains, dégraissés et dépoussiérés. Ne pas utiliser sur support basique (maçonnerie, béton, marbre...). APPLICATION Étant donné la diversité des supports sanitaires acryliques, un essai de convenance préalable est nécessaire. Lisser à l’eau savonneuse, serrer...